Power Delivery Architecture & Design
Architect and design high‑current power delivery modules (from mA to 100+ A) for ATE systems.
Develop fast‑response voltage/current sourcing circuits optimized for dynamic load conditions, droop control, and transient performance.
Implement advanced power‑stage topologies (buck, multiphase, linear, hybrid) tailored for semiconductor test environments.
Design for wide operating ranges, including high‑voltage rails, low‑voltage/high‑current rails, and dynamic voltage scaling.
Power Integrity & Transient Performance
Optimize power integrity across the full PDN (instrumentation → cabling → loadboard → DUT).
Model and mitigate droop, overshoot, ringing, and ground bounce under fast load steps.
Perform simulation and analysis of loop stability, compensation networks, and transient response.
Ensure compliance with DUT power‑up sequencing, ramp rates, and timing constraints.
Protection, Reliability & Safety
Design robust protection systems including OCP, OVP, OTP, short‑circuit protection, and fault‑isolation mechanisms.
Implement fast fault‑response circuits to protect sensitive DUTs and ATE hardware.
Conduct reliability analysis, derating studies, and thermal modeling for long‑term stability.
Support HALT/HASS, stress testing, and failure‑mode investigations.
Switching, Routing & Load Management
Develop efficient high‑current solutions for routing power to multiple DUT pins or sites.
Engineer low‑impedance, low‑loss paths for high‑current delivery with attention to thermal and mechanical constraints.
Collaborate with mechanical teams on heatsinking, airflow, and thermal interface design.
Bring‑Up, Debug & Validation
Lead bring‑up of new power‑delivery modules, performing root‑cause analysis of analog, digital, and mixed‑signal issues.
Execute characterization plans for load regulation, transient response, efficiency, thermal behavior, and fault handling.
Use advanced lab equipment (power analyzers, high‑bandwidth scopes, current probes, electronic loads) to validate performance.
ATE System Integration
Ensure power‑delivery modules meet ATE system‑level requirements for timing, triggering, synchronization, and software control.
Collaborate with firmware teams on control loops, telemetry, calibration, and fault‑reporting algorithms.
Create and use ATE test programs to validate instrument and system level designs.
Support integration with loadboards, probecards, and DUT power‑delivery networks.
Cross‑Functional Collaboration
Work with product engineering, test engineering, and silicon teams to define power‑delivery requirements for new devices.
Provide technical mentorship and contribute to power‑delivery design standards and best practices.
All About You
8- 10+ years of experience in power electronics, high‑current power delivery, or instrumentation hardware design.
Strong expertise in switching power supplies, multiphase regulators, linear regulators, and power‑stage design.
Experience with power integrity, transient analysis, and compensation/stability design.
Proficiency with SPICE simulation, PDN modeling tools, and PCB design tools.
Hands‑on experience with power measurement equipment and high‑current test setups.
Strong analytical and debugging skills.
Experience designing power‑delivery modules for ATE instrumentation.
Knowledge of dynamic voltage scaling, digital power control, and telemetry systems.
Familiarity with high‑current connectors, cabling, and low‑impedance mechanical design.
Understanding of thermal modeling, heatsink design, and system‑level thermal constraints.
Bachelor’s or Master’s degree in Electrical Engineering or related field.
Compensation
The base salary range for this role is $141,400 - $226,200. This range is a good faith estimate, and the amount of base salary will correspond with experience and skill set. This range can also fluctuate depending on demand and location.
Incentive Plan: This job is eligible for discretionary bonus(es) based on financial performance.
Benefits
Teradyne offers a variety of robust health and well-being benefit programs, including medical, dental, vision, Flexible Spending Accounts, retirement savings plans, life and disability insurance, paid vacation & holidays, tuition assistance programs, and more. Please click here to see details.
#LI-KD1
Job Segment
Thermal Engineering, Testing, Hardware Engineer, Electronics Engineer, Instrumentation, Engineering, Technology
Apply now »
Apply now
Apply Now
Start applying with LinkedIn
Start
Please wait...
Find similar jobs
- Engineering,
- Corporate Functions-tw,
- Corporate Functions-ko,
- Corporate Functions-ja,
- Corporate Functions-cn
© Teradyne Inc. 1994-2026 All rights reserved. Teradyne is an equal opportunity/affirmative action employer and all qualified applicants will receive consideration for employment without regard to race, color, religion, gender, sexual orientation, gender identity and expression, ethnicity or national origin, age, marital status, genetic information, military service, pregnancy, political affiliation, union membership, disability status, protected veteran status, or any other characteristic protected by law. ATTENTION APPLICANTS WITH DISABILITIES: If you're unable to access Teradyne's on-line job application due to a disability you may visit any one of our locations including our Corporate Office at 600 Riverpark Drive, North Reading, MA and request a paper application form. In addition, you may also contact the HR Service Center by phone at 978-370-3041 or email at HR.Service.Center@teradyne.com for additional assistance. We are a VEVRAA Federal Contractor. In compliance with US Labor Laws pertaining to “Pay Transparency Nondiscrimination Provision”, details can be viewed in this link, https://bit.ly/3iBiwO1. Please be aware of fraudulent hiring representation. All legitimate communications from the company will come from a Teradyne employee with the @teradyne.com domain. If you have any concerns that a communication may be fraudulent and you would like to confirm whether it is, please navigate and reach out through the Contact Us page.