The Coater Operator is required to stand/walk on a continuous basis while performing general required activities (primarily on concrete surfaces). The Coater Operator is not required to stand/balance on any atypical or uneven surfaces.
The employee is required to sit on an Occasional basis while completing paperwork.
The Coater Operator is required to Bend, Twist, Crawl, Squat, and/or Kneel on an occasional basis, primarily while cleaning rollers or line repair during "web breaks".
The Coater Operator primarily works while reaching between waist and shoulder height (frequent basis). Additional work may require the employee to work from knee to waist height (occasional); from floor to knee height (occasional); and above shoulder height (occasional) during web breaks.
The Coater Operator is required to work while bending the neck up on an occasional basis while performing quality assurance checks and line inspections. This may occur for less than 30 minutes at a time. Additionally, the employee will work while bending the neck down (up to 30 minutes) during computer data entry on an occasional basis.
The Coater Operator may be required to climb stairs on the line machine (occasional basis) as a part of typical job activities. The Coater Operator does not climb ladders as a part of general job activities.
The Coater Operator is required to perform handling, fingering and operating controls with hands on a frequent basis while performing general machine operations.
Secondary Tasks: Assisting Coater Assistant and/or Coater Helper
The Coater Operator may assist Coater Helper move metal line shafts (3-inch to 9-inch diameter) within 5-feet. Additionally, the Coater Operator may be required to lift/move cores within 5-feet to load on the 505/506/509 Line. Cores may weigh up to 40 pounds and may be located anywhere from knee to shoulder height on the racks. The cores must first be pulled out from storage racks. This may occur on an occasional basis.
The Coater Operator may assist the Assistant or Helper push rolls. The rolls weigh anywhere from 3000 to 5000 pounds. The rolls are pushed on a dolly-track located on the ground adjacent to each Line. While on the track, the roll requires up to 90 pounds of force to initiate movement. After movement, the rolls require up to 20 pounds of force to continue moving.
The Coater Operator may be required to assist the Assistant or Helper to pull cores out of racks on an occasional basis. Cores may weigh up to 40 pounds and may be located anywhere from knee to shoulder height on the racks.
While performing duties as an Assistant or Helper, the employee will primarily work while reaching between waist and shoulder height (frequent basis) Additional work may require the employee to work from knee to waist height (occasional); from floor to knee height (occasional); and above shoulder height (occasional).
As an Assistant or Helper, the employee may be required to climb stairs on the individual line machine on an occasional basis and climb a ladder on the 505/506/509 Line to change filters.
As an Assistant or Helper, the employee will perform handling, fingering and operating controls with hands on a frequent basis for general machine operations and general tasks. The employee may be required to operate a fork truck to retrieve rolls.
Tools & Equipment
General tools (hammer, utility knife, wrench, screwdriver, etc.)
Skimmer
Pneumatic table
Roll pusher
Scraper
Splitter
Dolly
Electronic inventory gun
Tape
Hoist
Computer
Environmental, Health & Safety
Safety Equipment
Safety Glasses
Hearing Protection (minimum NRR 18)
Work Gloves
Steel Toe Work Boots
Work Gloves and Armguards (during sampling)
Nomex Sleeves (Line 507 only)
Safety Program Participation
Standard Safety Orientation
Hearing Conservation Program
Lockout/Tagout Program
Environmental Training
General Environmental Awareness
HAZWOPER Awareness
Administrative
Day-to-day task structures have minimal variation.
The Coater Operator spends most of the shift within the MACtac Facility's Coating Department.
The Coater Operator may have up to 50% workload per shift associated with computer and paperwork.
The Coater Operator performs most allocated work standing.
Scope
Direct Reports: No
Physical Requirements: Heavy
Reports to: Shift Leader
Location: Scranton, PA
Selection Criteria
Education
Minimum High School Diploma or GED
Experience
Must have at least 6 months Lift Truck experience or be able to pass a Lift Truck licensing test.
Disclaimers
The above information on this description has been designed to indicate the general nature and level of work performed by employees within this classification. It is not designed to contain or be interpreted as a comprehensive inventory of all duties, responsibilities, and qualifications required of employees assigned to this job.
It is the policy of Mactac that all employees are employed at the will of Mactac for an indefinite period and are subject to termination at any time, for any reason, with or without cause or notice. At the same time, employees may terminate their employment at any time and for any reason.
Equal Opportunity Employer. All qualified candidates will receive consideration for employment and will not be discriminated against based on race, color, religion, sex, sexual orientation, gender identify, national origin, protected veteran status, disability, age, pregnancy, genetic information, creed, citizenship status, marital status or any other consideration prohibited by law or contract.
We will not accept unsolicited resumes from agencies. Please do not send agency resumes to our website or Mactac and affiliated employees.