Use industrial engineering line-design tools (layout/simulation software, cell-design methodology) to model and design the line, including U-shaped cell configurations for flexible, low-waste flow.
Deploy Manufacturing Execution System (MES) excellence practices on the line, real-time production tracking, OEE monitoring, digital work instructions, and full traceability, in partnership with MES teams.
Design and implement test fixtures and automated test procedures for functional test, RF test, and cellular connectivity validation (signal test, antenna tuning verification, conducted/radiated test fixtures).
Own End-of-Line testing and calibration procedures, ensuring functional, RF, and cellular connectivity performance is verified and calibrated prior to shipment.
Support to the automation developers and automation engineers and implement test fixtures and automated test procedures for functional test, RF test, and end-of-line quality checks.
Creates documentation for assembly and testing SOPs.
Lead root cause analysis and corrective actions for yield loss, defects, and field returns related to hardware or connectivity performance, together with the Quality Manager and RMA Responsible.
Collaborate with Purchasing department on component sourcing, second-source qualification, and obsolescence management for electronic components, in collaboration with the RD department.
Develop process documentation: work instructions, process flow diagrams, control plans, and FMEAs (Design FMEA and Process FMEA - Failure Modes and Effects Analysis).
Support New Product Introduction (NPI) activities including PVT (Production Validation Test), pilot runs, and MP (Mass Production - production ramp).
Drive continuous improvement initiatives (Lean, Six Sigma, Kaizen) to reduce cost, cycle time, and defect rates.
Ensure compliance with relevant standards (IPC-A-610, FCC/CE/PTCRB certification requirements for cellular devices, RoHS/REACH).
Collaborate with contract manufacturers EMS/CM partners on process transfer, line setup, and ongoing production support.
Sub-System Technical Fluency
Not expected to design these sub-systems personally, but must be technically fluent enough to dialogue with, challenge, and discuss on cost and performance with suppliers and the EMS partners on:
Visual inspection systems (AOI, machine vision), coverage, false-call rates, and cost/performance trade-offs.
Pick-and-place equipment, placement accuracy, speed, and component range.
Stacking and handling systems, part presentation, and material flow.
Calibration systems, functional test sequencer, cycle time.
Test sequencers, test step architecture, parallelization.
Cycle time, line- and station-level cycle time analysis and its impact on takt time and capacity.
Required Qualifications
Bachelor's degree in Industrial Engineering, Electrical Engineering, Manufacturing Engineering, or related field (or equivalent experience).
3+ years of experience in industrial/manufacturing engineering for electronic products.
Solid understanding of electronic components: passives, semiconductors, connectors, cellular modules, antennas, and power management components.
Hands-on experience with DFM/DFA principles for PCB assemblies and mechanical enclosures.
Working knowledge of hardware design fundamentals, schematics, PCB layout considerations.
Mastery of the design tools industrial engineers use to define manufacturing lines, end to end.
Hands-on experience implementing Manufacturing Execution System (MES) excellence practices: OEE tracking, real-time production monitoring, digital work instructions, and traceability.
Experience with SMT assembly processes, reflow profiles, and inspection methods (AOI, X-ray, ICT).
Strong analytical skills with experience in root cause analysis (8D, 5-Why, Fishbone).
Preferred Qualifications
Familiarity with IoT/M2M product development and low-power wireless design considerations.
Six Sigma Green Belt/Black Belt certification.
Experience working directly with overseas EMS/CM partners.
Knowledge of statistical process control (SPC) and quality management systems (ISO 9001).
Scripting/data analysis skills (Python, SQL, or similar) for yield and process data analysis.
Key Skills
CategorySkills
ManufacturingDFM/DFA, SMT processes, test fixture design, NPI, PVT, MP
MES (Manufacturing Execution System)MES excellence practices, OEE tracking, real-time monitoring, digital work instructions, traceability
Sub-System FluencyVisual inspection, pick-and-place, stacking/handling, calibration, test sequencers, cycle time
ElectronicsKnowledge in Component selection, BOM review and optimization, RF fundamentals, power electronics
Hardware DesignKnowledge in Schematic/PCB review
QualityFMEA, root cause analysis, IPC-A-610, SPC
ToolsERP systems (D365), Excel/data analysis tools
Soft SkillsCross-functional collaboration, documentation, project coordination
Physical / Work Environment
May require occasional travel to manufacturing sites or contract manufacturer facilities.
Combination of office/lab and production floor environment.
Responsibilities
1) Process Design Engineering: Carry out a range of activities under the guidance of more senior colleagues to support the analysis of information and the specification of the methods and process steps, as well as the plant, machinery, and equipment, required to design and continuously improve manufacturing or materials processes and process systems. 2) Engineering Solutions Design: Contribute to the development of, and implement feasibility testing of, proposed engineering solutions to provide feedback and data to validate the design. 3) Engineering Standards Specification: Carry out a range of activities under the guidance of more senior colleagues to support the drafting of engineering standards and specifications and the evaluation of the effectiveness of those standards. 4) Engineering Inspections: Carry out inspections under the supervision of senior colleagues to evaluate the quality of engineering works and/or the integrity of existing installations or structures, and make recommendations to senior colleagues on the remedial works needed to ensure conformance with specifications and regulatory requirements. 5) Testing: Use product specifications to design test procedures and standards. 6) Data Collection and Analysis: Collate and analyze data using preset tools, methods, and formats. Involves working independently. 7) Improvement/Innovation: Identify shortcomings in existing processes, systems, and procedures, and use established change management programs to address them. 8) Recommendations: Advise managers how to apply a wide variety of existing procedures and precedents. 9) Project Management: Work within an established project management plan to achieve specific goals. 10) Personal Capability Building: Develop own capabilities by participating in assessment and development planning activities as well as formal and informal training and coaching; gain or maintain external professional accreditation, where relevant, to improve performance and fulfill personal potential. Maintain an understanding of relevant technology, external regulation, and industry best practices through ongoing education, attending conferences, and reading specialist media.
Tasks
- 1) Interpret engineering drawings, sketches, or diagrams.
- 2) Conduct time and motion studies to identify opportunities to improve worker efficiency.
- 3) Plan the flow of work or materials to maximize efficiency.
- 4) Develop or implement programs to address problems related to production, materials, safety, or quality.
- 5) Modify equipment or processes to improve resource or cost efficiency.
- 6) Analyze operational, production, economic, or other data, using statistical procedures.
- 7) Oversee or inspect production processes.
- 8) Analyze, estimate, or report production costs.
- 9) Develop or conduct quality control tests to ensure consistent production quality.
- 10) Compile operational data to develop cost or time estimates, schedules, or specifications.
- 11) Collect and analyze data related to quality or industrial health and safety programs.
- 12) Prepare layouts of machinery or equipment, using drafting equipment or computer-aided design (CAD) software.
- 13) Prepare schedules for equipment use or routine maintenance.
- 14) Prepare reports regarding inventories of raw materials or finished products.
Educational Requirements: Short-Cycle Tertiary Education
General Experience Requirement: Experience enables job holder to deal with the majority of situations and to advise others (Over 3 years to 6 years)
Managerial Experience Requirement: Basic experience of coordinating the work of others (4 to 6 months)